Project bogey man. It's legal :-)

Acually washed it today lol also give the 1/4 a polish to see what it comes up like. Came up goooood!

Also swapped the fuel cap over for my new black one and found its got a stainless filler neck! bonus!





4x4 anyone?




Shine


floor looking new



Linkages all built ready to fit!

Looking good mate. A lot on nice new bits there... Powdercoating will really finish it off. Will you get the jigsaw put back together before the agm? Is that the plan?

Where did you lay your hands on a new speedo cablE

I sell them, £22.50 posted, should be in my ebay shop. If not drop me a pm.

Hugh, it WILL be at the agm! Lol fingers crossed.

been working on it today (yes a sunday), stripped and de mouse poo'd the interior. also gave it a polish (inside) lol







Can you tell the origional colour?

Also cleaned up the manky, dirty mouldy dash to find its mint!

Why did the picture have 2 driver's side tail lamp clusters?

Also, nice effort!

Oh yes?

Bugger!! Have to send 1 back, should have been a pair! Lol

Done a few bits today.

this included 4 tins of this and dinatrol (more liquid) being sprayed in the doors, rear 1/4s, boot lid, front panel, sills. should keep it rust free for a while!



which made it look loike this


Was running out of the door holes and sills so its got most places.


Had the rear stub axels come in today, last 2 in the country.


stripped out all the old running gear and started to build back up!



couldnt go any further as im waiting on my new brake dust shields to arrive before i can build the hubs up.

Hubs are awaiting pianting, diddnt go powder in the end as there was to much that needed to be masked so they will be POR15 chassis blacked, new bearings, new hubs and dust shields.


Archs have litrelly been covered in under seal! no chance of any water getting in here!



Also under sealed the lower bay, was some iffy paint so i wire brushed it all off and degreased it.


Tomorrow should see the rack, coilovers and hubs refitted (fingers crossed for the back plates) i might even fit the rear brakes etc ready for pipework.

gunna look amazing mate, really nice! you going to put an original grill on it?

Very nice!

Gonna be a minter!

Got your work cut out for the AGM, but I'm sure you can do it!

Will keep watching to see your progress…

Yes, will have stock lights and single light grill, the grill on it is to be sold on.

Interiors now sorted untill I find some Porsche fronts to go in, will be getting the black leather from my white gti and that's getting a set of white stripe seats from sphmk1.

Engine will be the deciding factor on getting it to the agm. Got my weber manifold today, takes a downdraught carb, never seen one before!

Still toying with dropping the turbo technics engine in it???

TURBO IT

looks good fella, lots of nice new shiney things on it will look good when done

No back plates today so not nuch to report :cry:

Fitted coilovers and rack, pressed the bearings in the hub carriers & painted them, also picked up the new hubs. and postie brought me some rear arch spats.

Rack fitted, with poly bush's


shiney new hubs


Arch spats (they are black not grey)

burn the midnight oil and it will make AGM :-)

LOL, i cant do much untill i get it rolling again, then it will only be glass, interior and engine.

Where did you get you new hubs from?

My secret stock! Lol

So today my back plates arrived at last!



pressed in the new hubs and they looked like this


Fitted on the car




Couldnt be arsed to do any more as im to bloody hot, oh and i for got a key part! Discs!!!

just picked up some new 256mm discs ready for the vauxhall conversion.

Tomorrow it WILL be rolling again!

Nice. Are they stainless back plates?